AVAYA 6424D M MANUAL PDF

If you need a larger conference call, you can order a MeetMe conference here. To add another party to a call. Press CONF again. Repeat steps 1 through 3 for additional conference connections. When the button is depressed, the other person on the call cannot hear your conversation. The light above the button will turn on.

Author:Vitaur Vudomi
Country:Ghana
Language:English (Spanish)
Genre:Sex
Published (Last):9 February 2013
Pages:183
PDF File Size:13.30 Mb
ePub File Size:3.22 Mb
ISBN:924-3-71765-218-6
Downloads:85318
Price:Free* [*Free Regsitration Required]
Uploader:Sazahn



If you need a larger conference call, you can order a MeetMe conference here. To add another party to a call. Press CONF again. Repeat steps 1 through 3 for additional conference connections. When the button is depressed, the other person on the call cannot hear your conversation.

The light above the button will turn on. Press SPKR. Place or answer the call. Adjust speakerphone volume if necessary. For raising or lowering the volume of the speakerphone. Press the up arrow to raise the volume. Press the down arrow to lower the volume. Press the call appearance button of the incoming call the green light will be flashing slowly. To return to a held call Press the call appearance button of the held call green light next to the button will be flashing rapidly.

Dial 88, you will hear a succession of beeps. Hang up. Dial 22, you will hear a succession of beeps. To answer a phone in you pick-up group if configured by I. Begin talking immediately. Programming Speed Dial buttons Speed dial buttons must be programmed by I.

Contact your Computing Coordinator or send an e-mail to telecom support. Changing the ringtone To change the ringtone on your telephone leave the telephone on hook and press the CONF button. Using the Softkeys You can display any of the softkey features by pressing the MENU button and then the softkey below the feature abbreviation.

When the feature is active, and arrow appears above the feature. However, if the feature requires you to dial a telephone number or extension, such as Call Forwarding, you will temporarily see the digits you are dialing rather than the arrow, above the feature name.

Answering a Bridged Call To Answer a bridged call. As this list is virtual, there is no way from the phone to view the list so it becomes important to write down the information or contact I.

Dial Personal List number 1, 2,or 3. If after you press the list number you get a waive-off tone, please contact the helpdesk at Dial list item Dial number you want to store up to 24 digits. You may be able to use the softkeys to add special features such as Pause, Mark, Wait, or Suppress into the telephone numbers programmed on the button.

Your second list is numbered list 1 in the system. Keep this in mind when you access and use your lists. You will hear a 3-burst priority ring when both you and the called extension are idle.

Pick up handset to be connected to the call. This feature must be enabled by I. The on-phone directory information is based on Caller-ID information, so some people may not appear in the on-phone directory. Using the on-phone directory Press the button below Dir.

Related Pages.

GROMOBRANSKA INSTALACIJA PDF

Avaya 6424D+M User Manual

Zolok In the data mode, data transmitted to the data terminal consists of one start bit, eight information bits, and one stop bit. Modular Interface Capabilities Press the call appearance button of the held call. Page 22 Chapter 2: Page 13 Press for odd. Unless you only want to temporarily change options, it is important to save any changes by copying pA to one of the stored profiles. If the feature is successfully administered on the feature button, thedisplay shows: While you are using the d, activate the speaker by pressingSpkr. In the event of a power failure, pA values are overwritten by values in p1. Organization Of This Guide Using your thumb, press down on the center of the tray.

LA CHUNGA MARIO VARGAS LLOSA PDF

Avaya 6424D+M Digital Phone (700276132)

Page 7 Note: When a modular base unit is used with the Headset jack, the handset should remain plugged into the Handset jack. The privacy of the Whisper Page announcement cannot be guaranteed when telephones have modular base units other than the M10L Comcode: ; PEC: The M10L is the only modular base unit that should be used for the Series telephones. Page 8 — — — Supra Monaural Noise-Canceling NC — Same as above with noise-canceling microphone that reduces background noise transmission by up to 75 percent. Supra Binaural — Sound in both ears. Supra Binaural Noise-Canceling NC — Same as above with noise-canceling microphone on flexible boom; features windscreen and reduces background noise transmission by up to 75 percent. Page 9 The top line of each softkey feature menu screen shows you the status of each of the four features.

Related Articles