Press the R button to increase the red tint and decrease the blue tint. ALoosen the camera fastening screw with a screwdriver BTo remove, turn the camera unit in the anticlockwise direction 5. Never push objects of any kind into this appliance through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Insert the camera unit into the ceiling hole. When doing so, be careful not to catch the cables in the outer case.
|Published (Last):||9 June 2006|
|PDF File Size:||13.40 Mb|
|ePub File Size:||12.20 Mb|
|Price:||Free* [*Free Regsitration Required]|
Press the R button to increase the red tint and decrease the blue tint. ALoosen the camera fastening screw with a screwdriver BTo remove, turn the camera unit in the anticlockwise direction 5.
Never push objects of any kind into this appliance through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Insert the camera unit into the ceiling hole. When doing so, be careful not to catch the cables in the outer case.
Draw the fall prevention wire mounted to the ceiling slab and the cable out from the ceiling in advance. See illustration below 3. CDismantle the fall prevention wire. However, there is no guarantee that interference will not occur in a particular installation. H Set the video setting switches on the camera unit before mounting it. Adjusting brightness This adjustment only needs to be made when required.
In this case, turn on the power after waiting for a few hours. Correction may take several seconds for completion. This is fk-cv4e for internal synchronization LL Line Lock: This is due to the built-in lens performance and is not a malfunction. Unauthorized substitutions may result in fire, electric shock, or other hazards. Q Pan fastening Screw Ensure to loosen the screw before setting. The openings should never be blocked by placing the appliance on a bed, sofa, rug, or other similar surface.
If the ceiling is not strong enough, make sure to apply reinforcement to the ceiling before installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. G Function selection switches 1. When installing a mixture of these models, select a cable length according to the power tj-cv4e of each model. When there is a new alarm input while the lens is at the alarm position, the lens continues to remain in the alarm position for 15 seconds upon the last alarm input.
As a result, when it is used under low light conditions, the camera sensitivity is automatically boosted and the picture may look uneven.
Always adjust the rotation by holding this knob. When changing modes, bright portions of image may be emphasized but this is not a failure of tk-cv44e camera. If it jcc contaminated seriously, clean the tk-vv4e part with a cloth or a tissue which has been soaked in a solution of water and a neutral detergent. Class 2 only E-type: Be sure to loosen the screw before adjusting. Before beginning to operate this unit, please read the instruction manual carefully in order to make sure that the best possible performance is obtained.
Registration of home position is enabled. Lower the protection cover and connect the connectors. Do not allow anything to rest on the power cord. Remove tkcv4e dome cover. When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Tighten using your hand instead. Most 10 Related.
Tk—cv4e a test monitor that cannot be left open is connected to this terminal, the jfc level when connected to the video signal output connector may deteriorate and appear dark. H Set the video setting switches on the camera unit before mounting it. However, there is no guarantee that interference will not occur in a particular installation. Applying force on the lens unit may damage it. Take care when handling it. Isolated power supply only 9: Security Cameras by Megan Wollerton Nov 8, Turn the ring in the anti-clockwise direction to remove. The camera automatically captures the image in color when the subject is bright, and in black and white mode when it is dark.
Jvc TK-C215V4U - CCTV Camera Manuals
Tataur Please refer carefully to the table for each cable during connection. When installing the camera onto the electric box, install it using the supplied adaptor ring. Solder or crimp After mounting is completed, adjust the images while checking the actual image. White-spot correction As a general characteristic unique to CCDs, white-spots may appear on the screen with age. Business users If you wish to dispose of this tk-xv4e, please visit our web page www. Be respectful, keep it civil and stay on topic.
JVC TK-C215V4E Dome camera